Texas Instruments X-Loader 1.5.0 (Mar 27 2011 - 17:37:56)
Beagle xM
Reading boot sector
Loading u-boot.bin from mmc
U-Boot 2011.03-rc1-00000-g9a3cc57-dirty (Apr 01 2011 - 17:41:42)
OMAP36XX/37XX-GP ES2.1, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz
OMAP3 Beagle board + LPDDR/NAND
I2C: ready
DRAM: 512 MiB
NAND: 0 MiB
MMC: OMAP SD/MMC: 0
*** Warning - readenv() failed, using default environment
In: serial
Out: serial
Err: serial
Beagle xM Rev C
No EEPROM on expansion board
Die ID #112a00029ff80000016830100e017018
Hit any key to stop autoboot: 0
OMAP3 beagleboard.org # mmc init
OMAP3 beagleboard.org # mmcinfo
Device: OMAP SD/MMC
Manufacturer ID: 2
OEM: 544d
Name: SD04G
Tran Speed: 25000000
Rd Block Len: 512
SD version 2.0
High Capacity: Yes
Capacity: 3963617280
Bus Width: 4-bit
OMAP3 beagleboard.org # setenv bootargs 'console=ttyS2,115200n8 vram=12M omapfb.mode=dvi:1024x768MR-16@60 omapfb.debug=y omapdss.def_disp=dvi'
OMAP3 beagleboard.org # fatload mmc 0 0x80909000 uImage
reading uImage
2297468 bytes read
OMAP3 beagleboard.org # bootm 0x80909000
## Booting kernel from Legacy Image at 80909000 ...
Image Name: Linux
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2297404 Bytes = 2.2 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 2.6.35.8 (vivek@HPX64) (gcc version 4.4.3 (gcc-4.4.3_cos_gg_51096) ) #1 Tue Dec 20 14:26:58 IST 2011 ()
CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: OMAP3 Beagle Board
Memory policy: ECC disabled, Data cache writeback
OMAP3630 ES1.0 (l2cache iva sgx neon isp 192mhz_clk )
SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
Reserving 12582912 bytes SDRAM for VRAM
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
Kernel command line: console=ttyS2,115200n8 vram=12M omapfb.mode=dvi:1024x768MR-16@60 omapfb.debug=y omapdss.def_disp=dvi root=/dev/mmcblk0p2t
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 256MB 256MB = 512MB total
Memory: 502900k/502900k available, 21388k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
vmalloc : 0xe0800000 - 0xf8000000 ( 376 MB)
lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc002e000 ( 152 kB)
.text : 0xc002e000 - 0xc0416000 (4000 kB)
.data : 0xc0430000 - 0xc0463740 ( 206 kB)
Hierarchical RCU implementation.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:402
Clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz
omap_hwmod: l3_hwmod: cannot be enabled (3)
omap_hwmod: l4_core_hwmod: cannot be enabled (3)
omap_hwmod: l4_per_hwmod: cannot be enabled (3)
omap_hwmod: l4_wkup_hwmod: cannot be enabled (3)
Reprogramming SDRC clock to 332000000 Hz
GPMC revision 5.0
IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
Total of 96 interrupts on 1 active controller
OMAP GPIO hardware version 2.5
OMAP clockevent source: GPTIMER12 at 32768 Hz
Console: colour dummy device 80x30
Calibrating delay loop... 503.12 BogoMIPS (lpj=1966080)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
NET: Registered protocol family 16
OMAP3 Beagle Rev: unknown 2
Found NAND on CS0
Registering NAND on CS0
OMAP DMA hardware revision 5.0
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c_omap i2c_omap.1: bus 1 rev4.0 at 2600 kHz
twl4030: PIH (irq 7) chaining IRQs 368..375
twl4030: power (irq 373) chaining IRQs 376..383
twl4030: gpio (irq 368) chaining IRQs 384..401
regulator: VUSB1V5: 1500 mV normal standby
regulator: VUSB1V8: 1800 mV normal standby
regulator: VUSB3V1: 3100 mV normal standby
twl4030_usb twl4030_usb: Initialized TWL4030 USB module
regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby
regulator: VDAC: 1800 mV normal standby
regulator: VPLL2: 1800 mV normal standby
regulator: VSIM: 1800 <--> 3000 mV at 1800 mV normal standby
i2c_omap i2c_omap.3: bus 3 rev4.0 at 100 kHz
Advanced Linux Sound Architecture Driver Version 1.0.23.
Switching to clocksource 32k_counter
musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
musb_hdrc musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NetWinder Floating Point Emulator V0.97 (double precision)
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc.
msgmni has been set to 982
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
OMAP DSS rev 2.0
OMAP DISPC rev 3.0
OMAP VENC rev 2
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
console [ttyS2] enabled
serial8250.3: ttyS3 at MMIO 0x49042000 (irq = 70) is a ST16654
brd: module loaded
loop: module loaded
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver rndis_host
usbmon: debugfs is not available
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
No device for DAI omap-mcbsp-dai-0
No device for DAI omap-mcbsp-dai-1
No device for DAI omap-mcbsp-dai-2
No device for DAI omap-mcbsp-dai-3
No device for DAI omap-mcbsp-dai-4
OMAP3 Beagle/Devkit8000 SoC init
asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
ALSA device list:
#0: omap3beagle (twl4030)
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
Power Management for TI OMAP3.
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
fbcvt: 1024x768@60: CVT Name - .786M3-R
Console: switching to colour frame buffer device 128x48
regulator_init_complete: incomplete constraints, leaving VDAC on
/build/beagleboard/tmp/portage/sys-kernel/chromeos-kernel-0.0.1-r316/work/chromeos-kernel-0.0.1/drivers/rtc/hctosys.c: unable to open rtc dev)
Waiting for root device /dev/mmcblk0p2...
mmc0: new high speed SDHC card at address bd69
mmcblk0: mmc0:bd69 SD04G 3.69 GiB
mmcblk0: p1 p2 p3
EXT3-fs: barriers not enabled
kjournald starting. Commit interval 5 seconds
EXT3-fs (mmcblk0p2): warning: maximal mount count reached, running e2fsck is recommended
EXT3-fs (mmcblk0p2): using internal journal
EXT3-fs (mmcblk0p2): recovery complete
EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
VFS: Mounted root (ext3 filesystem) on device 179:2.
Freeing init memory: 152K
EXT3-fs: barriers not enabled
kjournald starting. Commit interval 5 seconds
EXT3-fs (mmcblk0p3): warning: maximal mount count reached, running e2fsck is recommended
EXT3-fs (mmcblk0p3): using internal journal
EXT3-fs (mmcblk0p3): recovery complete
EXT3-fs (mmcblk0p3): mounted filesystem with ordered data mode
Unhandled prefetch abort: debug event (0x002) at 0x000499e8
Unhandled prefetch abort: debug event (0x002) at 0x000499e8
Unhandled prefetch abort: debug event (0x002) at 0x000499f0
Unhandled prefetch abort: debug event (0x002) at 0x000499f0
Unhandled prefetch abort: debug event (0x002) at 0x000499f0
Unhandled prefetch abort: debug event (0x002) at 0x000499e8
Unhandled prefetch abort: debug event (0x002) at 0x000499e8
Unhandled prefetch abort: debug event (0x002) at 0x000499e8
Unhandled prefetch abort: debug event (0x002) at 0x000499e8
Unhandled prefetch abort: debug event (0x002) at 0x000499e8
Unhandled prefetch abort: debug event (0x002) at 0x000499e8
Unhandled prefetch abort: debug event (0x002) at 0x000499e8
Unhandled prefetch abort: debug event (0x002) at 0x000499e8
Unhandled prefetch abort: debug event (0x002) at 0x000499e8
Unhandled prefetch abort: debug event (0x002) at 0x000499f0
Unhandled prefetch abort: debug event (0x002) at 0x000499e8
Unhandled prefetch abort: debug event (0x002) at 0x000499f0
Unhandled prefetch abort: debug event (0x002) at 0x000499e8
Unhandled prefetch abort: debug event (0x002) at 0x000499e8
Unhandled prefetch abort: debug event (0x002) at 0x000499e8
Unhandled prefetch abort: debug event (0x002) at 0x000499e8